amax-1220 amax-1240 specifcations pulse type motion control ? motor driver support pulse-type servo ? number of axes amax-1220: 2 amax-1240: 4 ? interpolation linear and circular ? max. output speed 6.5 mpps ? step count range 134, 217, 728 ? pulse output type out/dir, cw/ccw, a/b phase ? position counter 134, 217, 728 ? home modes 13 ? velocity profles t-curve, s-curve ? local i/o machine interfaces: el+/-, org and sd (slow down) for each axis servo driver interfaces: alm, rdy, svon, inp, break for each axis position compare i/o: ltc, cmp for each axis(only available for amax-1240-ae) simultaneous move within multiple modules: csta/cstp (simultaneously start/stop) for each model general purpose i/o: amax-1220 supports 8xdi and 8xdo encoder interface ? input type a/b phase, cw/ccw ? counts per enc. cycle x1, x2, x4 (ab phase only) ? input range low: 0 ~ 0.5v high: 3.5 ~ 7v ? isolation protection 2,500 v rms ? max. input frequency 2 mhz @ 5 v general ? bus type amonet rs-485 ? certifcation ce, fcc class a ? connectors rj-45 x 2 are for communication port db-26 connector by transfer cable to servo drives. other are screw terminal type connectors ? dimensions (l x w x h) 141 x 108 x 60 mm (5.6" x 4.3" x 2.4") ? system power 2 w @ 24 v typical consumption output channel power consumption 120w typical, 240w max. input channel power consumption amax-1220: 8 w @ 24 v external power (max.) amax-1240: 10 w @ 24 v external power (max.) ? system power input 24 v dc within 200 mv ripple ? humidity 5 ~ 95% rh, non-condensing (iec 60068-2-3) ? operating temperature 0 ~ 60c (32 ~ 140f) ordering information ? AMAX-1220-AE economic 2-axis amonet motion control module ? amax-1240-ae advanced 4-axis amonet motion control module accessories ? pcl-10153pa5-2e 50-pin cable to panasonic a4 and a5 servo, 2 m ? pcl-10153pa5ls-2e 50-pin cable to panasonic minas a servo, 2 m ? pcl-10153ys5-2e 50-pin cable to yaskawa sigma v servo, 2 m ? pcl-10153mj3-2e 50-pin cable to mitsubishi j3 servo, 2 m ? pcl-10153da2-2e 50-pin cable from adam-3955/adam-3956 to delta a2 servo, 2 m introduction amax-1220 and amax-1240 have compact open frame designs for horizontal placement and an interface connector mounted on the board. with a transfer cable to servo drive, both models can conveniently connect to mitsubishi j3, yaskwa sigma v and panasonic a4/a5. the amax-1220 is an economic 2-axis amonet slave module which supports motion functionality in point-to-point (ptp), linear & circular interpolation, simultaneously start/ stop among multiple slave modules, and brake signal to servo for emergence consideration. the amax-1240 is an advanced 4-axis amonet slave module which not only supports amax-1220 motion functionality, but also supports advanced features in position compare and triggering function. both linear interval and table setups are supported. ? end limit logic is switchable (high or low active) ? boardid is switchable ? easily visible led indicators on board to do diagnosis ? direct wire to servo drive to save terminal board space while installation ? max. 6.5 mhz, 4-axis pulse output ? 28 bits counter for incremental encoder ? horizontal installation for for servo or stepping motor driver ? suitable for din-rail mounting open frame type 2/ 4-axis amonet motion slave modules new amax-1220 amax-1240 rohs compliant 2002/95/ec all product specifications are subject to change without notice all product specifications are subject to change without notice last updated : 5-may-2015 www.advantech.com/products online download features
|
